Una línea de productos de recuperación de disolventes con opciones de tanque de almacenamiento de 50, 100 y 150 L. Revise el flujo de disolvente, la alimentación de vapor y los requisitos de líquido recuperado antes de seleccionar una configuración.
Compare VS-50, VS-100 y VS-150 por capacidad del tanque, potencia y dimensiones de instalación. La capacidad del tanque es un valor de almacenamiento; evalúe el rendimiento de recuperación por separado para su flujo de disolvente.
Confirme la composición de la alimentación de vapor, las unidades de flujo y la conexión del proceso para la configuración seleccionada. La salida de líquido utiliza un arreglo de bomba de diafragma. Revise los requisitos de destilación de la alimentación de líquido por separado.
Review the specifications alongside your process conditions and installation requirements. The quotation should confirm the configuration, connections and required documentation.
Review the standard specifications below. Dimensions are listed as length × width × height. Confirm the final configuration and installation dimensions in the quotation and approved drawing before ordering.
| Modelo | VS-50 | VS-100 | VS-150 |
|---|---|---|---|
| Source model | SZ-DWH-50L | SZ-DWH-100L | SZ-DWH-150L |
| Capacidad del tanque | 50 L | 100 L | 150 L |
| Total power | 4 kW | 8 kW | 18,5 kW |
| Reference supply | Trifásico 380 V | Trifásico 380 V | Trifásico 380 V |
| Dimensions (L × W × H), mm | 1,200 × 1,200 × 1,600 | 1,500 × 1,200 × 2,000 | 723 × 560 × 2,200 |
| Alimentación de vapor húmedo — confirme las unidades antes de dimensionar | ≤20 L/s | ≤50 L/s | ≤80 L/s |
| Cooling system | Direct expansion | Direct expansion | Direct expansion |
Provide your site voltage and frequency so electrical compatibility can be confirmed before ordering.
Direct-expansion cooling and diaphragm-pump liquid output are part of the reference configuration. Confirm inlet conditions, connections and the recovered-liquid destination during process review.
Provide the identity and composition of the stream, expected loading, temperature and operating pattern. Include any changes between production batches.
State the intended use of the recovered liquid and the measurable quality or outlet condition required. Confirm the method used to verify the result.
Define the receiving vessel, output connection and handling procedure. Tank volume is a storage parameter and should not be substituted for a recovery-rate specification.
Proporcione la identidad del disolvente, la composición, la concentración de vapor, la temperatura, la humedad y la carga esperada. Confirme el objetivo de calidad del líquido recuperado y la compatibilidad de los materiales en contacto con el flujo.
Para instalaciones en áreas peligrosas, confirme la clasificación aplicable y la certificación requerida antes de realizar el pedido. Verifique las unidades de alimentación de vapor y las condiciones de operación con el proveedor antes de dimensionar el equipo.
Provide representative process conditions and the treatment result you need so the configuration can be assessed for your application.
The three sizes are listed in the specification table above. Select around the measured feed and required output conditions. The largest storage tank or highest airflow does not automatically provide the best result for an undefined solvent stream.
The VS line and VR line use separate model prefixes and different sizing references. VS lists storage volume and wet-vapour feed; VR lists airflow and collection-tank volume. Do not directly compare these values as if they measured the same process capacity.
Provide an installation sketch, connection positions, available floor space and service clearances. Confirm the final drawing rather than relying on the photograph alone.
State the electrical supply and operating conditions. Confirm the control interface and commissioning requirements for the quoted configuration.
Request the operating manual and maintenance instructions for the actual build. Agree the inspection routine and any site-specific requirements before commissioning.
Review the specified protection functions and settings for the selected configuration, including power-loss, circuit-fault, overtemperature and high-level protection. VS includes low-water protection; VR includes phase-loss and exhaust-overheat protection. Confirm any required certification separately.
The AI-enhanced series image illustrates a representative configuration. Confirm the selected size and delivered arrangement in the quotation and approved drawing.
Specify your site voltage and frequency. Confirm electrical compatibility and any required adaptation in the quotation.
Suitability depends on your fluid or vapour composition, contamination and operating conditions. Agree the treatment target and any required sample testing before ordering.
Provide process composition, operating temperature, expected loading, required treatment schedule, installation sketch and utilities. State the result you need so the configuration can be assessed against it.
Solicite una revisión de la configuración propuesta de la Serie VS. Incluya las condiciones de operación y un esquema del diseño de conexión previsto para que los requisitos del equipo y la documentación puedan verificarse juntos.
Solicitar una revisión de la Serie VS
